Your Atlant washing machine generates error F15: what does the error code mean, what to do, how to fix the malfunctions that caused it?
We will consider all this below, give practical advice and clear recommendations on how to remove the error.
What does error F15 Atlant mean: decryption and reasons
Fault codes are displayed on the electronic displays of modern AGRs to warn the owner of a breakdown. In this case, SM Atlant shows an error because a water leak has occurred.
There are three reasons that could cause the F15 error:
- Depressurization of the tank.
- Damage to the cuff of the hatch.
- Violation of the integrity of the elements that make up the waste water discharge system.
A noticeable sign of damage: the washing machine is leaking.
DIY repair
The Atlant washing machine gives the code F15, and on the floor you found a puddle. Fix the problem yourself without resorting to the help of a wizard. If F15 is displayed, you can do the following:
- Ensure tank integrity. It is necessary to disassemble the machine and inspect it at the time of damage, cracks, rust, etc. If the tank is destroyed, it needs to be replaced.
- Check the integrity of the manhole cuff. From prolonged or improper use, the rubber seal may wear out and burst. If the cuff is damaged, it must be replaced in order to reset the errors.
- Check for leaks in all elements of the drain system. Hoses and nozzles during the use of the SMA could significantly suffer - burst, crack, break or wipe. If you find damaged items, you need to replace them with whole ones.
Important! Less often, the machine may leak due to a breakdown of the drain pump, detergent drawer or leak from the bearing.
Troubleshooting F15
Now, knowing when the Atlant washing machine shows the F15 code on the display, begin to consistently check all the nodes of the water drainage system. If you find unsuitable parts, change them.
Hoses and fittings
The most common cause of leaks is a violation of the integrity of the hoses and pipes. These rubber elements are fragile and wear out quickly, especially if the water is not of the highest quality.
Water intake hose
If there is a cause of leakage in the water inlet hose, this can be determined even if the SM does not work. Carefully inspect the hose and its connection to the CM housing. If the hose is damaged, replace it. If the connection is loose, change the gasket.
Water drain hose
In this case, the SMA will flow during the spin phase or when draining. Check the connection of the hose to the pump, inspect the hose along its entire length.
Found a hole or crack? The solution is to replace the part.
Branch pipes
If you find that the machine leaks at the stage of filling the washing water, and after filling the tank, the flow stops, the reason may be in the nozzle. It connects the filler valve to the powder cuvette.
Check the integrity of the unit by unscrewing the top cover of the washer.
Also, a leak may occur due to drain or water inlets. It is necessary to check them and replace if necessary.
Leaks through the cuff of the hatch
The cuff could be damaged in two ways:
- Small sharp objects.
- Dry out and burst with time.
If there is time and desire, try to repair the cuff - provided that the damage is small. For these purposes, ordinary rubber bicycle or boat patches are suitable.
Tank leak
If all these reasons are excluded, and the Atlant continues to flow, then the tank is to blame. How to fix it?
The tightness of the tank may be compromised for several reasons:
- Crack. Requires full tank replacement. It is better not to try to seal the crack, this will help for a while.
- Halves were leaked. Often the tank consists of 2 parts, between which there is a rubber gasket. If it has worn out, the tank is leaking. In this case, an almost complete disassembly of the SM Atlant will be required.
Pump leak
Often, Atlant cars are leaking due to a breakdown of the drain pump. Access to it is also provided through the bottom of the machine. Remove the pump and inspect it. If you find chips and cracks - without hesitation, replace the pump with a new one.
Detergent drawer
Often, a powder receiver causes leaks. Too much water pressure may be to blame for this - try screwing the valve on, loosening the pressure. If this does not help, the machine is still flowing, and F15 is on, inspect the tray. It may be damaged along the edges through which leakage occurs.